Smc-networks SMC2552W-G2-17 Manual de usuario Pagina 223
- Pagina / 296
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Command Line Interface
7-86
7
Command Mode
Global Configuration
Command Usage
Bridge priority is used in selecting the root device, root port, and designated
port. The device with the highest priority becomes the STP root device.
However, if all devices have the same priority, the device with the lowest MAC
address will then become the root device.
Example
bridge-link path-cost
Use this command to configure the spanning tree path cost for the specified port.
Syntax
bridge-link path-cost <index> <cost>
• index - Specifies the bridge link number on the wireless bridge. (Range: 1-6
required on wireless interface only)
• cost - The path cost for the port. (Range: 1-65535)
Default Setting
19
Command Mode
Interface Configuration
Command Usage
• This command is used by the Spanning Tree Protocol to determine the best
path between devices. Therefore, lower values should be assigned to ports
attached to faster media, and higher values assigned to ports with slower
media.
• Path cost takes precedence over port priority.
Example
bridge-link port-priority
Use this command to configure the priority for the specified port.
Syntax
bridge-link port-priority <index> <priority>
• index - Specifies the bridge link number on the wireless bridge. (Range: 1-6
required on wireless interface only)
• priority - The priority for a port. (Range: 1-255)
Enterprise AP(config)#bridge stp-bridge priority 40000
Enterprise AP(config)#
Enterprise AP(if-wireless a)#bridge-link path-cost 1 50
Enterprise AP(if-wireless a)#
- EliteConnect 2
- SMC2552W-G2 2
- 2.4GHz Wireless Access Point 2
- Copyright 3
- Japan VCCI Class B 5
- EC Conformance Declaration 5
- Safety Compliance 8
- OMPLIANCES 10
- COMPLIANCES 11
- Table of Contents 14
- Contents 21
- Chapter 1: Introduction 22
- Indicators 23
- Antennas 23
- Component Description 24
- Introduction 25
- Security Slot 25
- Console Port 25
- Ethernet Port 25
- Features and Benefits 26
- System Defaults 27
- Hardware Installation 33
- Chapter 3: External Antennas 34
- External Antennas 35
- Installation Procedures 36
- Network Topologies 39
- Infrastructure Wireless LAN 40
- Network Configuration 41
- Required Connections 44
- Initial Configuration Steps 45
- Logging In 46
- Initial Configuration 47
- Advanced Configuration 49
- System Identification 50
- TCP / IP Settings 52
- SSH Settings 58
- Authentication 59
- Filter Control 64
- WDS Settings 68
- AP Management 74
- Administration 75
- Upgrading Firmware 76
- System Log 79
- Configuring SNTP 81
- Configuring SNMPv3 Users 89
- Configuring SNMPv3 Targets 93
- Radio Interface 100
- System Configuration 101
- Configuring Wi-Fi Multimedia 104
- Security 109
- Enabling the VAPs 113
- Wi-Fi Protected Access (WPA) 120
- Configuring 802.1X 126
- Status Information 129
- Station Status 132
- Event Logs 135
- Chapter 7: 138
- Command Line Interface 138
- Entering Commands 139
- Command Completion 140
- Getting Help on Commands 140
- Showing Commands 140
- Enterprise AP#show s? 141
- Enterprise AP#show s 141
- Exec Commands 142
- Configuration Commands 142
- Command Groups 143
- General Commands 144
- System Management Commands 148
- APmgmtIP 158
- APmgmtUI 159
- System Logging Commands 165
- System Clock Commands 170
- DHCP Relay Commands 175
- SNMP Commands 177
- Flash/File Commands 192
- RADIUS Client 196
- 802.1X Authentication 202
- 802.1x session-timeout 204
- 802.1x-supplicant enable 205
- 802.1x-supplicant user 205
- MAC Address Authentication 207
- Filtering Commands 210
- WDS Bridge Commands 214
- Spanning Tree Commands 220
- Ethernet Interface Commands 225
- Wireless Interface Commands 230
- Rogue AP Detection Commands 246
- Wireless Security Commands 251
- Link Integrity Commands 260
- IAPP Commands 264
- VLAN Commands 265
- WMM Commands 267
- Appendix A: Troubleshooting 272
- Troubleshooting 273
- 10/100BASE-TX Pin Assignments 274
- Straight-Through Wiring 275
- Crossover Wiring 276
- Wiring Map for Serial Cable 277
- Appendix C: Specifications 278
- °C (32 to 122 °F) 279
- °C (32 to 158 °F) 279
- General Specifications 280
- Sensitivity 281
- Transmit Power 281
- Operating Range 283
- Glossary 284
- Virtual Access Point (VAP) 288
- Virtual LAN (VLAN) 288
- Wi-Fi Protected Access 288
- WPA Pre-shared Key (PSK) 288
- Model Number: SMC2552W-G2-17 295
- Pub. Number: 150000030500E 295
- E052006-DT-R01 295
- 38 Tesla 296
- Irvine, CA 92618 296
- Phone: (949) 679-8000 296
Relacionado con productos y manuales para Hardware Smc-networks SMC2552W-G2-17
Hardware Smc-networks SMC2482W Manual de usuario
(50 paginas)
(50 paginas)
Hardware Smc-networks EX120-SDN1 Manual de usuario
(13 paginas)
(13 paginas)
Hardware Smc-networks SMC7204BRA Manual de usuario
(56 paginas)
(56 paginas)
Hardware Smc-networks SMC2835W Manual de usuario
(33 paginas)
(33 paginas)
Hardware Smc-networks SMCWTVG Manual de usuario
(5 paginas)
(5 paginas)
Hardware Smc-networks SMCWAA-B Manual de usuario
(51 paginas)
(51 paginas)
Hardware Smc-networks 486DX4 Manual de usuario
(81 paginas)
(81 paginas)
Hardware Smc-networks EZ Connect 2-Port ADSL Bridge Router SMC7003ADSL Manual de usuario
(2 paginas)
(2 paginas)
Hardware Smc-networks SMC9452TX-2 Manual de usuario
(41 paginas)
(41 paginas)
(124 paginas)
Hardware Smc-networks SMCHP1D-ETH Manual de usuario
(26 paginas)
(26 paginas)
Hardware Smc-networks SMC7008ABR Manual de usuario
(46 paginas)
(46 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales