SMC Networks TigerSwitch Manual de usuario Pagina 207
- Pagina / 518
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
VLAN C
ONFIGURATION
3-157
- If ingress filtering is disabled and a port receives frames tagged for
VLANs for which it is not a member, these frames will be flooded to
all other ports (except for those VLANs explicitly forbidden on this
port).
- If ingress filtering is enabled and a port receives frames tagged for
VLANs for which it is not a member, these frames will be discarded.
- Ingress filtering does not affect VLAN independent BPDU frames,
such as GVRP or STP. However, they do affect VLAN dependent
BPDU frames, such as GMRP.
• GVRP Status – Enables/disables GVRP for the interface. GVRP
must be globally enabled for the switch before this setting can take
effect. (See “Displaying Bridge Extension Capabilities” on page 3-15.)
When disabled, any GVRP packets received on this port will be
discarded and no GVRP registrations will be propagated from other
ports. (Default: Disabled)
• GARP Join Timer
8
– The interval between transmitting requests/
queries to participate in a VLAN group.
(Range: 20-1000 centiseconds; Default: 20)
• GARP Leave Timer
8
– The interval a port waits before leaving a
VLAN group. This time should be set to more than twice the join time.
This ensures that after a Leave or LeaveAll message has been issued,
the applicants can rejoin before the port actually leaves the group.
(Range: 60-3000 centiseconds; Default: 60)
• GARP LeaveAll Timer
8
– The interval between sending out a
LeaveAll query message for VLAN group participants and the port
leaving the group. This interval should be considerably larger than the
Leave Time to minimize the amount of traffic generated by nodes
rejoining the group.
(Range: 500-18000 centiseconds; Default: 1000)
8. Timer settings must follow this rule: 2 x (join timer) < leave timer < leaveAll timer
- TigerSwitch 10/100 1
- Management Guide 3
- Glossary 19
- NTRODUCTION 27
- Table 1-1 Key Features 28
- ESCRIPTION 29
- System Defaults 33
- Table 1-2 System Defaults 34
- Required Connections 38
- ONNECTING 39
- Remote Connections 40
- Stack Operations 41
- Basic Configuration 42
- Setting Passwords 43
- Setting an IP Address 44
- Dynamic Configuration 45
- Community Strings 47
- Saving Configuration Settings 48
- Managing System Files 49
- AVIGATING 53
- The Mode can be 54
- Main Menu 55
- Manual Configuration 68
- Using DHCP/BOOTP 69
- Managing Firmware 71
- Console Port Settings 78
- Telnet Settings 80
- Configuring Event Logging 83
- RAM. (Range: 0-7, Default: 6) 84
- Remote Log Configuration 85
- Displaying Log Messages 88
- Resetting the System 91
- Setting the System Clock 92
- User Authentication 98
- ONFIGURING 100
- Command Usage 101
- Command Attributes 101
- UTHENTICATION 103
- Configuring HTTPS 104
- Configuring the Secure Shell 107
- Generating the Host Key Pair 110
- Field Attributes 110
- Configuring the SSH Server 112
- Configuring Port Security 114
- Displaying 802.1X Statistics 123
- Access Control Lists 127
- Setting the ACL Name and Type 128
- Console(config-std-acl)# 129
- Configuring a Standard IP ACL 130
- Configuring a MAC ACL 134
- Console(config-mac-acl)# 135
- Port Configuration 138
- Field Attributes (CLI) 139
- Basic Information: 139
- Configuration: 139
- Current Status: 140
- Creating Trunk Groups 143
- Configuring LACP Parameters 149
- ONFIGURATION 151
- Displaying LACP Port Counters 153
- Configuring Port Mirroring 161
- Configuring Rate Limits 163
- Rate Limit Configuration 164
- Showing Port Statistics 165
- Table 3-9 Port Statistics 166
- Figure 3-52 Port Statistics 170
- Address Table Settings 172
- Displaying the Address Table 173
- LGORITHM 179
- VLAN Configuration 192
- Assigning Ports to VLANs 193
- Displaying Current VLANs 198
- Command Attributes (Web) 198
- Command Attributes (CLI) 199
- Creating VLANs 200
- Private VLANs 209
- Configuring Private VLANs 211
- Associating VLANs 213
- Layer 2 Queue Settings 218
- Selecting the Queue Mode 222
- Layer 3/4 Priority Settings 224
- Mapping IP Precedence 225
- Mapping DSCP Priority 227
- Mapping IP Port Priority 229
- Mapping CoS Values to ACLs 231
- Multicast Filtering 233
- NTERFACE 243
- Telnet Connection 244
- Entering Commands 246
- Command Completion 247
- Getting Help on Commands 247
- Showing Commands 248
- Table 4-1 Command Modes 250
- Configuration Commands 251
- Command Line Processing 253
- Command Groups 254
- Line Commands 256
- Console(config)#line console 257
- Console(config-line)# 257
- Console#disconnect 1 267
- Console# 267
- Example 268
- General Commands 269
- Console#disable 271
- Console> 271
- Console#configure 271
- Console(config)# 271
- Console#reload 273
- Console(config-if)#end 273
- System Management Commands 275
- User Access Commands 277
- ANAGEMENT 279
- IP Filter Commands 280
- Web Server Commands 283
- Telnet Server Commands 287
- Secure Shell Commands 289
- Console#show ssh 298
- Event Logging Commands 301
- Table 4-18 Logging Levels 302
- SMTP Alert Commands 310
- Time Commands 314
- System Status Commands 320
- Related Commands 323
- Frame Size Commands 329
- Flash/File Commands 330
- Column Heading Description 335
- Authentication Commands 337
- Authentication Sequence 338
- RADIUS Client 341
- TACACS+ Client 345
- Port Security Commands 348
- 802.1X Port Authentication 350
- Access Control List Commands 361
- IP ACLs 362
- Table 4-34 IP ACLs 363
- Queue 0123 370
- 1,2 0,3 4,5 6,7 370
- Access-list ALS1 cos 0 371
- MAC ACLs 372
- Console#show mac access-list 375
- MAC access-list jerry: 375
- ACL Information 378
- Command Mode 379
- Privileged Executive 379
- SNMP Commands 380
- Interface Commands 387
- Console(config-if)# 389
- Mirror Port Commands 401
- Rate Limit Commands 403
- Default Setting 404
- Link Aggregation Commands 406
- GGREGATION 407
- Address Table Commands 420
- Spanning Tree Commands 425
- Console(config)#spanning-tree 427
- VLAN Commands 440
- Console(config)#vlan database 441
- Console(config-vlan)# 441
- Configuring VLAN Interfaces 443
- Displaying VLAN Information 450
- Command Function Mode Page 452
- XTENSION 459
- Priority Commands 464
- 1, 20, 34, 56, 7 468
- [no] map ip port 471
- IP Precedence Value 01234567 474
- CoS Value 01234567 474
- Console(config)#map ip dscp 475
- Multicast Filtering Commands 480
- ULTICAST 481
- ILTERING 481
- IP Interface Commands 491
- PECIFICATIONS 497
- Management Features 498
- Standards 499
- Management Information Bases 500
- ROUBLESHOOTING 501
- Using System Logs 503
- Glossary-1 505
- Glossary-2 506
- Glossary-3 507
- Glossary-4 508
- Glossary-5 509
- Glossary-6 510
- Glossary-7 511
- Glossary-8 512
Relacionado con productos y manuales para Los conmutadores de red SMC Networks TigerSwitch
(94 paginas)
(56 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.076 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales