Smc-networks 16 10BASE-T Manual de usuario Pagina 189
- Pagina / 384
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Line Commands
4-13
4
timeout login response
This command sets the interval that the system waits for a user to log into the CLI.
Use the no form to restore the default.
Syntax
timeout login response [seconds]
no silent-time
seconds - Integer that specifies the timeout interval.
(Range: 0 - 300 seconds; 0: disabled)
Default Setting
• CLI: Disabled (0 seconds)
• Telnet: 600 seconds
Command Mode
Line Configuration
Command Usage
• If a login attempt is not detected within the timeout interval, the connection is
terminated for the session.
• This command applies to both the local console and Telnet connections.
• The timeout for Telnet cannot be disabled.
• Using the command without specifying a timeout restores the default setting.
Example
To set the timeout to two minutes, enter this command:
Related Commands
silent-time (4-15)
exec-timeout (4-14)
exec-timeout
This command sets the interval that the system waits until user input is detected.
Use the no form to restore the default.
Syntax
exec-timeout [seconds]
no exec-timeout
seconds - Integer that specifies the number of seconds.
(Range: 0-65535 seconds; 0: no timeout)
Default Setting
CLI: No timeout
Telnet: 10 minutes
Console(config-line)#timeout login response 120
Console(config-line)#
- TigerSwitch 10/100 1
- Installation Guide 3
- Contents 7
- Chapter 1: Introduction 21
- Introduction 22
- System Defaults 25
- Connecting to the Switch 29
- Required Connections 30
- Basic Configuration 31
- Setting Passwords 32
- Setting an IP Address 32
- Initial Configuration 34
- Community Strings 34
- Managing System Files 36
- Using the Web Interface 37
- Home Page 38
- Panel Display 39
- Main Menu 40
- Manual Configuration 49
- Using DHCP/BOOTP 50
- Console#ip dhcp restart 4-186 51
- Console Port Settings 55
- * CLI only 56
- Telnet Settings 57
- Configuring Event Logging 59
- Remote Logs Configuration 61
- Displaying Log Messages 62
- Resetting the System 63
- Setting the System Clock 63
- Configuring SNTP 64
- User Authentication 68
- Configuring HTTPS 73
- Configuring the Secure Shell 75
- Generating the Host Key Pair 77
- Configuring the SSH Server 79
- Configuring Port Security 80
- Displaying 802.1x Statistics 87
- Access Control Lists 89
- Configuring a MAC ACL 94
- 1: Port Information only 98
- 2: Trunk Information only 98
- Configuring the Switch 100
- Port Configuration 101
- Creating Trunk Groups 102
- Configuring LACP Parameters 106
- Displaying LACP Port Counters 109
- Configuring Port Mirroring 115
- Configuring Rate Limits 116
- Console(config-if)# 117
- Showing Port Statistics 118
- Address Table Settings 122
- Console(config)# 123
- Displaying Global Settings 126
- Configuring Global Settings 129
- Displaying Interface Settings 132
- VLAN Configuration 137
- * Web Only 140
- Displaying Current VLANs 141
- Creating VLANs 143
- Private VLANs 149
- Configuring Private VLANs 151
- Console(config-vlan)# 152
- Layer 2 Queue Settings 156
- * CLI shows Queue ID 158
- Priority 158
- Selecting the Queue Mode 159
- Mapping IP Precedence 163
- Mapping DSCP Priority 164
- Mapping IP Port Priority 166
- Mapping CoS Values to ACLs 167
- Multicast Filtering 169
- Accessing the CLI 177
- Console Connection 177
- Telnet Connection 177
- Command Line Interface 178
- Entering Commands 179
- Showing Commands 180
- Console#show s? 181
- Console# 181
- Exec Commands 182
- Configuration Commands 182
- Command Line Processing 184
- Command Groups 185
- Line Commands 186
- Console(config)#line console 187
- Console(config-line)# 187
- Console#disconnect 1 194
- General Commands 195
- Console>enable 196
- Console#disable 196
- Console> 196
- System Management Commands 200
- Console(config)#prompt RD2 201
- RD2(config)# 201
- Console(config)#hostname RD#1 201
- IP Filter Commands 204
- Secure Shell Commands 210
- Console#configure 212
- Console(config)#ip ssh server 212
- Console(config)#logging on 219
- Console#clear logging 222
- Time Commands 225
- Console#show calendar 230
- 15:12:34 April 1 2004 230
- Console#light unit 1 230
- Frame Size Commands 236
- Console(config)#jumbo frame 237
- Flash/File Commands 239
- Console#delete 1:test2.cfg 240
- Authentication Commands 243
- 10 retransmit 5 key green 246
- Port Security Commands 251
- Console(config)#dot1x default 254
- Access Control List Commands 261
- IP ACLs 262
- Console(config-std-acl)# 263
- Console(config-ext-acl)# 265
- Console(config-mac-acl)# 269
- ACL Information 274
- SNMP Commands 275
- Interface Commands 280
- Mirror Port Commands 291
- Rate Limit Commands 293
- Console#show rate-limit 295
- Console(config-if)#exit 297
- Link Aggregation Commands 301
- Address Table Commands 305
- Spanning Tree Commands 309
- Console(config)#spanning-tree 310
- VLAN Commands 321
- Console(config)#vlan database 322
- Displaying VLAN Information 329
- Eth 1/ 6: 337
- GVRP configuration: Enabled 337
- Priority Commands 339
- Console(config)#map ip port 345
- Console(config)#map ip dscp 348
- Multicast Filtering Commands 352
- IP Interface Commands 361
- Console#show ip redirects 364
- IP default gateway 10.1.0.254 364
- Software Features 367
- Management Features 368
- Standards 368
- Management Information Bases 369
- Software Specifications 370
- Appendix B: Troubleshooting 371
- Using System Logs 372
- Glossary 373
- Glossary-6 378
- Virtual LAN (VLAN) 378
Relacionado con productos y manuales para Accesorios De Computador Smc-networks 16 10BASE-T
(522 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.055 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales