SMC Networks SMC6724L3 Manual de usuario Pagina 495
- Pagina / 618
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
M
ULTICAST
F
ILTERING
C
OMMANDS
4-209
Command Mode
Interface Configuration (VLAN)
Command Usage
• The switch must be using IGMPv2 for this command to take effect.
• This command defines how long any responder (i.e., client or router)
still in the group has to respond to a query message before the router
deletes the group.
• By varying the Maximum Response Interval, you can tune the
burstiness of IGMP messages passed on the subnet; where larger
values make the traffic less bursty, as host responses are spread out
over a larger interval.
• The number of seconds represented by the maximum response
interval must be less than the Query Interval (page 4-207).
Example
The following shows how to configure the maximum response time to
20 seconds:
Related Commands
ip igmp version (4-210)
ip igmp query-interval (4-207)
ip igmp last-memb-query-interval
Use this command to configure the last member query interval. Use the no
form of this command to restore the default.
Syntax
ip igmp last-memb-query-interval seconds
no ip igmp last-memb-query-interval
seconds - The report delay for the last member query. (Range: 1-255)
Console(config-if)#ip igmp max-resp-interval 20
Console(config-if)#
- TigerSwitch 10/100 1
- Management Guide 3
- NTRODUCTION 23
- ESCRIPTION 25
- System Defaults 30
- Required Connections 36
- ONNECTING 37
- Remote Connections 38
- Basic Configuration 39
- Setting Passwords 40
- Setting an IP Address 40
- Manual Configuration 41
- Dynamic Configuration 42
- Community Strings 43
- Saving Configuration Settings 45
- Managing System Files 46
- AVIGATING 51
- Using DHCP/BOOTP 68
- Managing Firmware 70
- Setting the System Clock 73
- Configuring SNTP 74
- Setting the Time Zone 75
- User Authentication 76
- Displaying 802.1x Statistics 87
- Access Control Lists 89
- Setting the ACL Name and Type 90
- Configuring a Standard IP ACL 91
- Configuring a MAC ACL 95
- ONFIGURING 100
- ONFIGURATION 101
- Configuring Address Pools 105
- Displaying Address Bindings 110
- Port Configuration 111
- Configuring Port Mirroring 118
- Showing Port Statistics 119
- Configuring Rate Limits 125
- Trunk Configuration 127
- Address Table Settings 132
- Displaying the Address Table 133
- LGORITHM 135
- Configuring Global Settings 140
- VLAN Configuration 150
- Assigning Ports to VLANs 151
- Displaying Current VLANs 156
- Creating VLANs 158
- Configuring Private VLANs 166
- Multicast Filtering 182
- IGMP Protocol 183
- ULTICAST 185
- ILTERING 185
- L3 - network core 192
- IP Routing 197
- Initial Configuration 198
- IP Switching 199
- Routing Path Management 200
- Routing Protocols 200
- Address Resolution Protocol 205
- Proxy ARP 206
- Basic ARP Configuration 207
- Console(config)# 209
- Displaying Local ARP Entries 211
- Displaying ARP Statistics 212
- IP Statistics 213
- Statistical Values 214
- ICMP Statistics 216
- UDP Statistics 218
- TCP Statistics 219
- Configuring Static Routes 220
- Displaying the Routing Table 221
- Autonomous System A 235
- Autonomous System B 235
- Configuring OSPF Areas 240
- Configuring OSPF Interfaces 246
- Configuring Virtual Links 252
- Console(config-router)# 253
- 255.255.0.0 4-253 257
- Configuring NSSA Settings 260
- * These items are read only 263
- Console# 266
- Configuring DVMRP 270
- CHAPTER 4 287
- COMMAND LINE 287
- INTERFACE 287
- Telnet Connection 288
- Entering Commands 289
- NTERFACE 290
- Showing Commands 291
- Exec Commands 293
- Configuration Commands 294
- Command Line Processing 296
- Command Groups 297
- Line Commands 299
- Console(config-line)# 303
- General Commands 310
- Console>enable 311
- Console#configure 313
- Console#reload 315
- Console(config-if)#end 315
- System Management Commands 317
- ANAGEMENT 319
- Time Commands 327
- Flash/File Commands 339
- Authentication Commands 346
- RADIUS Client 347
- UTHENTICATION 349
- 802.1x Port Authentication 352
- Access Control List Commands 360
- Console(config-std-acl)# 363
- permit host 10.1.1.21 369
- Console(config-mac-acl)# 371
- Console(config-if)# 373
- Command Function Mode Page 375
- SNMP Commands 376
- DHCP Commands 383
- DHCP Relay 385
- DHCP Server 388
- Console(config)#service dhcp 389
- Console(config-dhcp)# 391
- Interface Commands 404
- Command Usage 416
- Example 416
- Mirror Port Commands 419
- Rate Limit Commands 421
- Link Aggregation Commands 423
- GGREGATION 425
- Address Table Commands 427
- Aging time: 300 sec 431
- Spanning Tree Commands 432
- Console(config)#spanning-tree 433
- VLAN Commands 448
- Console(config)#vlan database 449
- Console(config-vlan)# 449
- Configuring VLAN Interfaces 450
- XTENSION 461
- Priority Commands 467
- Console(config)#map ip dscp 477
- Multicast Filtering Commands 482
- IGMP Commands (Layer 3) 491
- IP Interface Commands 501
- Related Commands 507
- IP Routing Commands 511
- Command Mode 529
- Privileged Exec 529
- 10.1.0.0/255.255.0.0 569
- Multicast Routing Commands 571
- Normal Exec, Privileged Exec 586
- ROUBLESHOOTING 597
- Glossary-1 603
- Glossary-2 604
- Glossary-3 605
- Glossary-4 606
- Glossary-5 607
- Glossary-6 608
- Glossary-7 609
- Glossary-8 610
Relacionado con productos y manuales para Software SMC Networks SMC6724L3
(962 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.033 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales