Smc-networks SMC7804WBRA Manual de usuario

viiTABLE OF CONTENTS1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1About the Barricade . . . . . . . . . . . .

ADVANCED SETUP4-57DDNSDynamic Domain Name Service (DDNS) provides users on the Internet with a method to tie their domain name to a computer or server

CONFIGURING THE BARRICADE4-58UPnP Click Enable to turn on the Universal Plug and Play function of the Barricade. This function allows the device to au

ADVANCED SETUP4-59ToolsUse the Tools menu to backup the current configuration, restore a previously saved configuration, restore factory settings, upd

CONFIGURING THE BARRICADE4-60Firmware UpgradeUse this screen to update the firmware or user interface to the latest versions. Download the upgrade fil

ADVANCED SETUP4-61ResetClick “APPLY” to reset the Barricade. The reset will be complete when the power LED stops blinking. If you perform a reset from

CONFIGURING THE BARRICADE4-62StatusThe Status page displays WAN/LAN connection status, firmware, and hardware version numbers, illegal attempts to acc

ADVANCED SETUP4-63The following items are included on the Status page: Item DescriptionINTERNET Displays WAN connection type and status. Click the Co

CONFIGURING THE BARRICADE4-64Finding the MAC address of a Network CardWindows 98/MEClick Start/Run. Type “winipcfg” and press “ENTER”.The MAC address

A-1APPENDIX ATROUBLESHOOTINGThis section describes common problems you may encounter and possible solutions to them. The Barricade can be easily monit

TROUBLESHOOTINGA-2LED IndicatorsLink LED is Off• Verify that the Barricade and attached device are powered on. • Be sure the cable is plugged into bot

TABLE OF CONTENTSviii4 Configuring the Barricade . . . . . . . . . . . . . . . . . . . . . . 4-1Navigating the Management Interface . . . . . . . .

TROUBLESHOOTINGA-3Management ProblemsCannot connect using the web browser• Be sure to have configured the Barricade with a valid IP address, subnet ma

TROUBLESHOOTINGA-4Wireless ProblemsA wireless PC cannot associate with the Barricade.• Make sure the wireless PC has the same SSID settings as the Bar

B-1APPENDIX BCABLESEthernet CableCaution: DO NOT plug a phone jack connector into any RJ-45 port. Use only twisted-pair cables with RJ-45 connectors t

CABLESB-2Each wire pair must be attached to the RJ-45 connectors in a specific orientation. The following figure illustrates how the pins on an Ethern

ETHERNET CABLEB-3Pin AssignmentsWith 100BASE-TX/10BASE-T cable, pins 1 and 2 are used for transmitting data, and pins 3 and 6 for receiving data.Strai

CABLESB-4Crossover WiringIf the port on the attached device has straight-through wiring (MDI), use crossover cable.Crossover Cable Pin AssignmentsEnd

ADSL CABLEB-5ADSL CableUse standard telephone cable to connect the RJ-11 telephone wall outlet to the RJ-45 ADSL port on the ADSL Router.Caution: Do n

CABLESB-6Figure B-3. RJ-11 PinoutsPin Signal Name Wire Color1Not used2 Line 2 Tip Black or White/Orange3 Line 1 Ring Red or Blue/White4 Line 1 Tip Gr

C-1APPENDIX CSPECIFICATIONSPhysical CharacteristicsPortsFour 10/100Mbps RJ45 PortsOne ADSL RJ11Two external dipole antennasADSL FeaturesSupports DMT l

SPECIFICATIONSC-2Security FeaturesPassword protected configuration accessUser authentication (PAP/CHAP) with PPPFirewall NAT NAPTVPN pass through (IPS

TABLE OF CONTENTSixA Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1B Cables . . . . . . . . . . . . . . . . . . . .

SPECIFICATIONSC-313 channels (ETSI)2 Channels (Spain)4 Channels (France)14 channels (Japan)Operating Channels IEEE 802.11g compliant:13 channels (US,

SPECIFICATIONSC-4Modulation Rate-Receiver Sensitivity Typical (dBm)802.11g - 6Mbps -88802.11g - 9Mbps -87802.11g - 12Mbps -84802.11g - 18Mbps -82802.1

SPECIFICATIONSC-5Standards Conformance Electromagnetic CompatibilityCE, ETSI, R&TTE, FCC part 15 class B & FCC part 68, ETS 300 328, ETS 300

SPECIFICATIONSC-6

FOR TECHNICAL SUPPORT, CALL:From U.S.A. and Canada (24 hours a day, 7 days a week) (800) SMC-4-YOU; Phn: (949) 679-8000; Fax: (949) 679-1481Fro

TABLE OF CONTENTSx

1-1CHAPTER 1INTRODUCTIONCongratulations on your purchase of the ADSL Barricade TM g, hereafter referred to as the "Barricade". We are proud

INTRODUCTION1-2• Firewall with Stateful Packet Inspection, client privileges, intrusion detection, and NAT• NAT also enables multi-user Internet acces

APPLICATIONS1-3• Shared IP AddressThe Barricade provides Internet access for up to 253 users via a single shared IP address. Using only one ISP accoun

INTRODUCTION1-4• Virtual Private Network (VPN)The Barricade supports three of the most commonly used VPN protocols — PPTP, L2TP, and IPSec. These prot

2-1CHAPTER 2INSTALLATIONBefore installing the ADSL Barricade TM g, verify that you have all the items listed under the Package Contents list. If any o

INSTALLATION2-2System RequirementsYou must meet the following minimum requirements:• ADSL line installed by your Internet Service Provider.• A PC usin

7HVOD,UYLQH&$3KRQH0ESV:LUHOHVVSRUW5RXWHUZLWKEXLOWLQ$'6/0RGHP)URP60&¶VOLQHRIDZDUGZLQQLQJFRQQHF

HARDWARE DESCRIPTION2-3The Barricade includes an LED display on the front panel for system power and port indications that simplifies installation and

INSTALLATION2-4LED IndicatorsThe power and port LED indicators on the front panel are illustrated by the following figure and table.Figure 2-2. Front

ISP SETTINGS2-5ISP SettingsPlease collect the following information from your ISP before setting up the Barricade:• ISP account user name and password

INSTALLATION2-6Phone Line ConfigurationInstalling a Full-Rate ConnectionIf you are using a full-rate (G.dmt) connection, your service provider will at

CONNECT THE SYSTEM2-7Installing a Splitterless Connection If you are using a splitterless (G.lite) connection, then your service provider will attach

INSTALLATION2-8Attach to Your Network Using Ethernet CablingThe four LAN ports on the Barricade auto-negotiate the connection speed to 10 Mbps Etherne

3-1CHAPTER 3CONFIGURING CLIENT PCAfter completing hardware setup by connecting all your network devices, you need to configure your computer to connec

CONFIGURING CLIENT PC3-2TCP/IP ConfigurationTo access the Internet through the Barricade, you must configure the network settings of the computers on

WINDOWS 98/ME3-32. In Control Panel, double-click the Network icon.3. In the Network window, under the Configuration tab, double-click the TCP/IP item

CONFIGURING CLIENT PC3-45. Windows may need your Windows 95/98/Me CD to copy some files. After it finishes copying, it will prompt you to restart your

Information furnished is believed to be accurate and reliable. However, no responsibility is assumed by our company for its use, nor for any infringem

WINDOWS 98/ME3-53. In the Internet Options window, click the Connections tab. Next, click the LAN Settings... button.4. Clear all the check boxes.5. C

CONFIGURING CLIENT PC3-6Obtain IP Settings from Your ADSL RouterNow that you have configured your computer to connect to your Barricade, it needs to o

WINDOWS NT 4.03-7Windows NT 4.01. On the Windows desktop, click Start/Settings/Control Panel.2. Double-click the Network icon.

CONFIGURING CLIENT PC3-83. In the Network window, Select the Protocols tab. Double-click TCP/IP Protocol.4. When the Microsoft TCP/IP Properties windo

WINDOWS NT 4.03-98. Windows may copy some files, and will then prompt you to restart your system. Click Yes and your computer will shut down and resta

CONFIGURING CLIENT PC3-102. In the Command Prompt window, type “IPCONFIG /RELEASE” and press the ENTER key.3. Type “IPCONFIG /RENEW” and press the ENT

WINDOWS 20003-11Windows 20001. On the Windows desktop, click Start/Settings/Network and Dial-Up Connections. 2. Click the icon that corresponds to the

CONFIGURING CLIENT PC3-12Disable HTTP ProxyYou need to verify that the “HTTP Proxy” feature of your web browser is disabled. This is so that your brow

WINDOWS 20003-133. Type “IPCONFIG /RENEW” and press the ENTER key. Verify that your IP Address is now 192.168.2.xxx, your Subnet Mask is 255.255.255.0

CONFIGURING CLIENT PC3-14Windows XP1. On the Windows desktop, click Start/Control Panel.2. In the Control Panel window, click Network and Internet Con

iLIMITED WARRANTYLimited Warranty Statement: SMC Networks, Inc. (“SMC”) warrants its products to be free from defects in workmanship and materials, un

WINDOWS XP3-152. In the Command Prompt window, type “IPCONFIG/RELEASE” and press the ENTER key.3. Type “IPCONFIG /RENEW” and press the ENTER key. Veri

CONFIGURING CLIENT PC3-16Configuring Your Macintosh ComputerYou may find that the instructions here do not exactly match your operating system. This i

CONFIGURING YOUR MACINTOSH COMPUTER3-173. If “Using DHCP Server” is already selected in the Configure field, your computer is already configured for D

CONFIGURING CLIENT PC3-183. Uncheck all check boxes and click OK.

4-1CHAPTER 4CONFIGURING THEBARRICADEAfter you have configured TCP/IP on a client computer, you can configure the Barricade using Internet Explorer 5.0

CONFIGURING THE BARRICADE4-2Navigating the Management InterfaceThe Barricade’s management interface consists of a Setup Wizard and an Advanced Setup s

SETUP WIZARD4-3Setup WizardTime ZoneClick on “Setup Wizard”. The first item in the Setup Wizard is Time Zone. For accurate timing of log entries and s

CONFIGURING THE BARRICADE4-4Parameter SettingSelect your Country and Internet Service Provider. This will automatically configure the Barricade with t

SETUP WIZARD4-5ConfirmThe Confirm page shows a summary of the configuration parameters. Check ADSL operation mode (WAN), Network Layer Parameters (WAN

CONFIGURING THE BARRICADE4-6If the parameters are correct, click “APPLY” to save these settings.Your Barricade is now set up. Go to “Troubleshooting”

LIMITED WARRANTYiiWARRANTIES EXCLUSIVE: IF AN SMC PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, CUSTOMER’S SOLE REMEDY SHALL BE REPAIR OR REPLACEMENT O

SETUP WIZARD4-7Parameter Setting - Country or ISP Not ListedIf your Country or Internet Service Provider is not listed select “Others”. This will allo

CONFIGURING THE BARRICADE4-8ISP use RFC1483 Bridging - Parameter SettingEnter the RFC1483 Bridging settings provided by your ISP. Note: You have three

SETUP WIZARD4-9Click “NEXT” to continue to the “Confirm” settings page.Go to “Confirm” on page 4-5 in the manual for details about the “Confirm” setti

CONFIGURING THE BARRICADE4-10ISP use PPPoE - Parameter SettingEnter the PPPoE (Point-to-Point Protocol over Ethernet) settings provided by your ISP. C

SETUP WIZARD4-11ISP use PPPoA - Parameter SettingEnter the PPPoA (Point-to-Point Protocol over ATM) settings provided by your ISP. Click “NEXT” to co

CONFIGURING THE BARRICADE4-12ISP use RFC1483 Routing - Parameter SettingEnter the RFC1483 Routing settings provided by your ISP. Click “NEXT” to conti

ADVANCED SETUP4-13Advanced SetupClick on the Advanced Setup picture. The left-hand side displays the main menu and the right-hand side shows descripti

CONFIGURING THE BARRICADE4-14DDNS Dynamic DNS provides users on the Internet with a method to tie their domain name(s) to a Dynamic or Static IP addre

ADVANCED SETUP4-15SystemTime SettingsSelect your local time zone from the drop down list. This information is used for log entries and client filterin

CONFIGURING THE BARRICADE4-16Password SettingsUse this page to change the password for accessing the management interface of the Barricade. Password

iiiCOMPLIANCESFederal Communication Commission Interference StatementThis equipment has been tested and found to comply with the limits for a Class B

ADVANCED SETUP4-17Remote ManagementBy default, management access is only available to users on your local network. However, you can also manage the Ba

CONFIGURING THE BARRICADE4-18DNSDomain Name Servers (DNS) are used to map a domain name (e.g., www.smc.com) with the IP address (e.g., 64.147.25.20).

ADVANCED SETUP4-19WANSpecify the WAN connection parameters provided by your Internet Service Provider (ISP).The Barricade can be connected to your ISP

CONFIGURING THE BARRICADE4-20PPPoEEnter the PPPoE (Point-to-Point over Ethernet) parameters here. Parameter DescriptionEnable/Disable Enables/disable

ADVANCED SETUP4-21ATMEnter ATM (Asynchronous Transfer Mode) function parameters here. Idle Time (Minute) Enter the maximum idle time for the Inte

CONFIGURING THE BARRICADE4-22Clone MAC AddressSome ISPs require you to register your MAC address with them. If this is the case, the MAC address of th

ADVANCED SETUP4-23ISPEnter the Internet Service Provider (ISP) name, user name, and password for each ISP connection you have. You can enter up to fou

CONFIGURING THE BARRICADE4-24LANUse the LAN menu to configure the LAN IP address and to enable the DHCP server for dynamic client address allocation.

ADVANCED SETUP4-25WirelessThe Barricade also operates as a wireless access point, allowing wireless computers to communicate with each other. To confi

CONFIGURING THE BARRICADE4-26Channel and SSIDYou must specify a common radio channel and SSID (Service Set ID) to be used by the Barricade Wireless Ro

COMPLIANCESivThe REN is used to determine the quantity of devices that may be connected to the telephone line. Excessive RENs on the telephone line ma

ADVANCED SETUP4-27SecurityTo make your wireless network safe, you should turn on the security function. The Barricade supports WEP (Wired Equivalent P

CONFIGURING THE BARRICADE4-28WEPIf you want to use WEP to protect your wireless network, you need to set the same parameters for the Barricade and all

ADVANCED SETUP4-29WPAWi-Fi Protected Access (WPA) combines temporal key integrity protocol (TKIP) and 802.1X mechanisms. It provides dynamic key encry

CONFIGURING THE BARRICADE4-30802.1XIf 802.1X is used in your network, then you should enable this function for the Barricade. Parameter Description802

ADVANCED SETUP4-31NATNetwork Address Translation allows multiple users to access the Internet sharing one public IP.

CONFIGURING THE BARRICADE4-32Address MappingAllows one or more public IP addresses to be shared by multiple internal users. This also hides the intern

ADVANCED SETUP4-33Virtual ServerIf you configure the Barricade as a virtual server, remote users accessing services such as web or FTP at your local s

CONFIGURING THE BARRICADE4-34Special Application Some applications require multiple connections, such as Internet gaming, video-conferencing, and Inte

ADVANCED SETUP4-35RoutingThese pages define routing related parameters, including static routes and RIP (Routing Information Protocol) parameters.

CONFIGURING THE BARRICADE4-36Static Route Click “Add” to add a new static route to the list, or check the box of an already entered route and click “M

COMPLIANCESvAustralia AS/NZS 3548 (1995) - Class BSMC contact for products in Australia is:SMC-AustraliaL9, 123 Epping Rd.,North Ryde, NSW AustraliaPh

ADVANCED SETUP4-37RIP Parameter DescriptionGeneral RIP ParametersRIP mode Globally enables or disables RIP.Auto summary If Auto summary is disabled, t

CONFIGURING THE BARRICADE4-38RIP sends routing-update messages at regular intervals and when the network topology changes. When a router receives a ro

ADVANCED SETUP4-39Routing Table Parameter DescriptionFlags Indicates the route status: C = Direct connection on the same subnet.S = Static route.R = R

CONFIGURING THE BARRICADE4-40FirewallThe Barricade Router’s firewall inspects packets at the application layer, maintains TCP and UDP session informat

ADVANCED SETUP4-41Access ControlAccess Control allows users to define the outgoing traffic permitted or not-permitted through the WAN interface. The d

CONFIGURING THE BARRICADE4-42To add the PC to the filtering table: 1. Click “Add PC” on the Access Control screen.2. Define the appropriate settings f

ADVANCED SETUP4-43MAC Filter The Barricade can also limit the access of hosts within the local area network (LAN). The MAC Filtering Table allows the

CONFIGURING THE BARRICADE4-44URL BlockingThe Barricade allows the user to block access to web sites from a particular PC by entering either a full URL

ADVANCED SETUP4-45Schedule RuleYou may filter Internet access for local clients based on rules. Each access control rule may be activated at a schedul

CONFIGURING THE BARRICADE4-46Intrusion Detection• Intrusion Detection FeatureStateful Packet Inspection (SPI) and Anti-DoS firewall protection (Defaul

COMPLIANCESviSafety ComplianceWichtige Sicherheitshinweise (Germany)1. Bitte lesen Sie diese Hinweise sorgfältig durch.2. Heben Sie diese Anleitung

ADVANCED SETUP4-47Scroll down to view more information. • Stateful Packet Inspection This is called a “stateful” packet inspection because it examines

CONFIGURING THE BARRICADE4-48“Enable SPI and Anti-DoS firewall protection” field and then check the inspection type that you need, such as Packet Frag

ADVANCED SETUP4-49• DoS Criteria and Port Scan CriteriaSet up DoS and port scan criteria in the spaces provided (as shown below). Note: The firewall d

CONFIGURING THE BARRICADE4-50DMZIf you have a client PC that cannot run an Internet application properly from behind the firewall, you can open the cl

ADVANCED SETUP4-51SNMPUse the SNMP configuration screen to display and modify parameters for the Simple Network Management Protocol (SNMP).CommunityA

CONFIGURING THE BARRICADE4-52TrapSpecify the IP address of the NMS to notify when a significant event is detected by the agent. When a trap condition

ADVANCED SETUP4-53ADSLADSL (Asymmetric Digital Subscriber Line) is designed to deliver more bandwidth downstream (from the central office to the custo

CONFIGURING THE BARRICADE4-54StatusThe Status screen displays information on connection line status, data rate, operation data and defect indication,

ADVANCED SETUP4-55The following items are included on this information page: Parameter DescriptionStatus Line Status Shows the current status of the A

CONFIGURING THE BARRICADE4-56Statistics (Superframes represent the highest level of data presentation. Each superframe contains regular ADSL frames, o