SMC Networks 2.4GHz Manual de usuario

5 | WLAN Driver/Utility Installation Step 1: Insert the SMCWUSB32 EZ Installation Wizard and Documentation CD. Step 2: Click the [Install Driver/Util

Step 4: Click the [Next] button to continue. Step 5: Choose the folder where the utility setup files will be installed. It is recommended to leave

Step 6: Please restart your computer to finish the installation of the SMCWUSB32.

6 | Utility Configuration NOTE: The following applies to Windows 98SE, Me, 2000. Under Windows XP, please use the Wireless Zero Configuration tool bui

Section 1.1 | Status This tab will show you the current profile of the wireless card. Click [Disable Connection] to entirely halt all wirelessly func

Section 1.2 | Profile The Profile tab allows to create or delete profiles and configure the wireless network settings. The options for Mode include I

For more secure data transmissions, it is recommended to enable WEP on your WLAN. Click the [Encryption] button to get to this configuration. The util

Section 1.4 | Statistics The Statistics tab is used to monitor TX and RX traffic of the wireless network. It also offers the detailed information on

Section 1.5 | About The About screen displays the version information and MAC address. USING WIRELESS ZERO CONFIGURATION 1) After completing the dr

3) You should see the SSID of your Wireless Base Station or adhoc network in the “Available wireless networks” window. High-light the desired networ

Copyright Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable. However, no responsibility is assumed by SMC for

5) Select your desired network from the “Available wireless networks” window and then click [Configure]. 6) You will be able to select the “Network

7 | Wireless Distance Table Important Notice Maximum distances posted below are actual tested distance thresholds. However, there are many variables s

8 | Troubleshooting If your computer cannot find the EZ Connect Wireless USB Adapter or the network driver does not install correctly, check the follo

• If your wireless station cannot communicate with a computer on the Ethernet LAN when configured for Infrastructure mode, try changing the wireless

9 | Frequently Asked Questions • What is a Wireless LAN? o A local area network that transmits over the air typically in an unlicensed frequency s

• What is Authentication Algorithm? o Authentication Algorithm is the means by which one station is authorized to communicate with another. In an Op

10 | Technical Specifications Standards: IEEE 802.11b compliant Wireless Data Rates (With Automatic Fall-back): 1/2/5.5/11 Mbps Data Modulation Te

Read Transfer Power Consumption: < 26mA Write Transfer Power Consumption: < 300mA Sleep Mode Power Consumption: < 150mA Flash Memory Size: 3

11 | Terminology 10BaseT - Physical Layer Specification for Twisted-Pair Ethernet using Unshielded Twisted Pair wire at 10Mbps. This is the most popu

Ethernet - A standard for computer networks. Ethernet networks are connected by special cables and hubs, and move data around at up to 10 million bit

Compliances FCC - Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the

which is implemented in the network adapters that are plugged into the machines. The actual communications path is the cable (twisted pair, coax, opti

Subnet Mask - A subnet mask, which may be a part of the TCP/IP information provided by your ISP, is a set of four numbers configured like an IP addre

EC Conformance Declaration – Class B SMC contact for these products in Europe is: SMC Networks Europe, Edificio Conata II Calle Fructuos Gelabert 6-8

1 | System Requirements • An available USB port • Windows 98SE/Me/2000/XP • A minimum of 10 MB of free disk space for installing the driver and ut

3 | Installation Instructions - Device Installation 1) Select an available USB port on the PC 2) Make sure the cap of the SMCWUSB32 is pushed down

4 | Flash Drive Installation NOTE: Installation processes may require the use of your original, licensed copy of Windows. Please have your Windows CD

Step 5: Once the system has copied the SMC drivers from the CD, it may then request files from your original Windows disk. Please insert the Windows C

Step 2: Insert the Driver CD and select the [Specify a location:] option. Clear the [Removable Media] checkbox. Then press the [Browse] button and loo