SMC Networks SMC2835W Manual de usuario

Step 4: Once all the necessary files have been copied, the driver installation is complete. Click [Finish] to exit the wizard. Step 5: You will then

Step 6: You have now completed the driver installation. Click [Finish] to initialize the adapter. Section 5.4 | Windows XP Step 1: After you have in

After clicking [Finish], you will see the following message in your system tray: 6 | Driver Verification Windows 98SE/Me/2000/XP Section 6.1

Step 3: The Device Status shows that the "This device is working properly". If there are any error messages displayed here, you will need to

7 | Utility Installation Windows 98SE/Me/2000/XP This Installation method makes the process as simple and Plug-and-Play as possible. Simply run

Step 4: You will be given the option to choose the location where the Configuration Utility will be installed. It is recommended to leave this at the

Step 5: Click [Next] to begin copying the utility files to your computer. You have now completed the utility installation process. Click [Finish] to

8 | Utility Configuration When the utility program is running, there will be a quick launch icon in the lower right-hand corner of the taskbar. The

Section 8.1 | Configuration When the Configuration Utility is initialized, the Configuration window may be immediately shown. This will show you the

Section 8.2 | Link Information Associated BSS ID: Shows the MAC Address of the associated Access Point Current Tx Rate: Current transmit rate value T

Copyright Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable. However, no responsibility is assumed by SMC for

Section 8.3 | IP Information The IP Information screen displays network connection information. Section 8.4 | Site Survey The Site Survey tab sc

Section 8.5 | Version Information The Version Information screen displays the version information.

9 | Disable Wireless Zero Configuration in Windows XP It is recommended that you use the SMC2835W Configuration Utility to manage your 54 Mbps W

10 | SMC Networks EZ Connect g Wireless Cardbus Adapter Maximum Distance Table Important Notice Maximum distances posted below are actual t

802.11b Wireless Distance Table Environmental Condition Speed and Distance Ranges 11 Mbps 5.5 Mbps 1-2 Mbps Outdoors: A line-of-sight environmen

11 | Troubleshooting Common Installation Problems Problems are often caused by conflicts with other devices installed in the same computer, or softwar

12 | Technical Specifications Standards: IEEE 802.11b and 802.11g-draft compliant Wireless Data Rates (With Automatic Fall-back): 802.11b = 1/2/5.5

LED Indicators: Activity (ACT) Network Link (LINK) Power Voltage: 3.3 Volt + 5% Power Consumption: Transmission mode - 480mA Receive mode - 380mA

13 | Frequently Asked Questions What is a Wireless LAN? A local area network that transmits over the air typically in an unlicensed frequency such

What is RTS Threshold? (Request To Send) An RS-232 signal sent from the transmitting station to the receiving station requesting permission to transmi

Compliances FCC - Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the

14 | Terminology 10BaseT - Physical Layer Specification for Twisted-Pair Ethernet using Unshielded Twisted Pair wire at 10Mbps. This is the most popu

Ethernet - A standard for computer networks. Ethernet networks are connected by special cables and hubs, and move data around at up to 10 million bits

the other device. There are typically one or two ports on a device that can be toggled between MDI (not crossed) and MDI-X (crossed). Medium Dependent

1 | System Requirements • Available 32-bit Cardbus PCMCIA Type II slot • Windows 98SE/Me/2000/XP • Minimum of 32MB RAM and 300 MHz CPU • Minimu

2 | Package Contents After unpacking the EZ Connect g SMC2835W 2.4GHz 54 Mbps Wireless Cardbus Adapter, check the contents of the box to be sure you

3 | Getting Started… Warning: • Network cards are sensitive to static electricity. To protect the card, avoid touching its electrical components a

4 | Driver Installation – Option 1 (Recommended) Windows 98SE/Me/2000/XP NOTE: Installation processes will require the use of your original, lic

5 | Driver Installation – Option 2 Windows 98SE/Me/2000/XP Section 5.1 | Windows 98SE NOTE: Installation processes will require the use of your

Step 7: Once all the necessary files are copied from the Windows CD, the driver install process will be complete. Click [Finish] to exit the wizard.