SMC Networks SMC8024L2 Manual de usuario

TigerSwitch10/100/1000Managed Ethernet Switch◆ 24 auto-MDI/MDI-X 10/100/1000BASE-T ports◆ 4 ports shared with 4 SFP transceiver slots◆ Non-blocking sw

COMPLIANCESviImportant! Before making connections, make sure you have the correct cord set. Check it (read the label on the cable) against the followi

COMPLIANCESviiVeuillez lire à fond l'information de la sécurité suivante avant d'installer le Switch:AVERTISSEMENT: L’installation et la dép

COMPLIANCESviiiBitte unbedingt vor dem Einbauen des Switches die folgenden Sicherheitsanweisungen durchlesen:WARNUNG: Die Installation und der Ausbau

COMPLIANCESixWarnings and Cautionary MessagesWar nings (in German)Environmental StatementThe manufacturer of this product endeavours to sustain an env

COMPLIANCESxEnd of Product Life SpanThis product is manufactured in such a way as to allow for the recovery and disposal of all included electrical co

xiTABLE OF CONTENTS1 About the TigerSwitch 10/100/1000 . . . . . . . . . . . . . . 1-1Overview . . . . . . . . . . . . . . . . . . . . . . . . .

TABLE OF CONTENTSxiiConnecting to a Power Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8Connecting to the Console Port

TABLE OF CONTENTSxiiiAPPENDICES:A Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-1Diagnosing Switch Indicators . . .

TABLE OF CONTENTSxiv

xvTABLESTable 1-1 Port Status LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4Table 1-2 Power Status LED . . . . . .

xviFIGURESFigure 1-1 Front Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1Figure 1-2 Rear Panel . . . . . . . . .

1-1CHAPTER 1ABOUT THETIGERSWITCH 10/100/1000OverviewSMC’s TigerSwitch 10/100/1000 SMC8024L2 is an intelligent Layer 2 switch with 24 10/100/1000BASE-T

ABOUT THE TIGERSWITCH 10/100/10001-2Switch ArchitectureThe switch employs a wire-speed, non-blocking switching fabric. This permits simultaneous wire-

DESCRIPTION OF HARDWARE1-3Description of Hardware10/100/1000BASE-T PortsThe switch contains 24 RJ-45 ports that operate at 10 Mbps or 100 Mbps, half o

ABOUT THE TIGERSWITCH 10/100/10001-4Figure 1-3 Port LEDs and Power LEDPower Supply SocketThe power socket is located on the rear panel of the switch.

FEATURES AND BENEFITS1-5power socket is for the AC power cord.Figure 1-4 Power Supply SocketFeatures and BenefitsConnectivity• 24 10/100/1000 Mbps po

ABOUT THE TIGERSWITCH 10/100/10001-6Expandability• 4 Small Form Factor Pluggable (SFP) transceiver slots (shared with 1000BASE-T ports)• Supports 1000

2-1CHAPTER 2NETWORK PLANNINGIntroduction to SwitchingA network switch allows simultaneous transmission of multiple packets via non-crossbar switching.

NETWORK PLANNING2-2Application ExamplesThe TigerSwitch 10/100/1000 is not only designed to segment your network, but also to provide a wide range of o

APPLICATION EXAMPLES2-3Central Wiring ClosetWith 24 parallel bridging ports (i.e., 24 distinct collision domains), this switch can collapse a complex

38 TeslaIrvine, CA 92618Phone: (949) 679-8000TigerSwitch 10/100/1000Installation GuideFrom SMC’s Tiger line of feature-rich workgroup LAN solutionsApr

NETWORK PLANNING2-4Remote Connections with Fiber CableFiber optic technology allows for longer cabling than any other media type. A 1000BASE-SX (MMF)

APPLICATION EXAMPLES2-5Making VLAN ConnectionsThe switch supports VLANs that can be used to organize any group of network nodes into separate broadcas

NETWORK PLANNING2-6Application Notes1. Full-duplex operation only applies to point-to-point access (such as when a switch is attached to a workstation

3-1CHAPTER 3INSTALLING THE SWITCHSelecting a SiteTigerSwitch 10/100/1000 units can be mounted in a standard 19-inch equipment rack or on a flat surfac

INSTALLING THE SWITCH3-2Ethernet CablingTo ensure proper operation when installing the switches into a network, make sure that the current cables are

EQUIPMENT CHECKLIST3-3Equipment ChecklistAfter unpacking the TigerSwitch 10/100/1000 unit, check the contents to be sure you have received all the com

INSTALLING THE SWITCH3-4MountingA TigerSwitch 10/100/1000 unit can be mounted in a standard 19-inch equipment rack or on a desktop or shelf. Mounting

MOUNTING3-5To rack-mount devices:1. Attach the brackets to the device using the screws provided in the Bracket Mounting Kit.Figure 3-2 Attaching the

INSTALLING THE SWITCH3-63. If installing a single switch only, turn to “Connecting to a Power Source” at the end of this chapter.4. If installing mult

INSTALLING AN OPTIONAL SFP TRANSCEIVER INTO THE SWITCH3-7Installing an Optional SFP Transceiver into the SwitchFigure 3-5 Inserting an SFP Transceive

Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable. However, no responsibility is assumed by SMC for its use, n

INSTALLING THE SWITCH3-8Note: SFP transceivers are hot-swappable. The switch does not need to be powered off before installing or removing a transceiv

CONNECTING TO THE CONSOLE PORT3-9Connecting to the Console Port The DB-9 serial port on the switch’s back panel is used to connect to the switch for o

INSTALLING THE SWITCH3-10

4-1CHAPTER 4MAKING NETWORKCONNECTIONSConnecting Network DevicesThe TigerSwitch 10/100/1000 units are designed to interconnect multiple segments (or co

MAKING NETWORK CONNECTIONS4-2Connecting to PCs, Servers, Hubs and Switches1. Attach one end of a twisted-pair cable segment to the device’s RJ-45 conn

TWISTED-PAIR DEVICES4-3Network Wiring ConnectionsToday, the punch-down block is an integral part of many of the newer equipment racks. It is actually

MAKING NETWORK CONNECTIONS4-4Fiber Optic SFP DevicesAn optional Gigabit SFP transceiver (1000BASE-SX, 1000BASE-LX or 1000BASE-ZX) can be used for a ba

FIBER OPTIC SFP DEVICES4-53. Connect one end of the cable to the LC port on the switch and the other end to the LC port on the other device. Since LC

MAKING NETWORK CONNECTIONS4-6Connectivity RulesWhen adding hubs (repeaters) to your network, please follow the connectivity rules listed in the manual

CONNECTIVITY RULES4-7100 Mbps Fast Ethernet Collision Domain10 Mbps Ethernet Collision DomainTable 4-3 Maximum 1000BASE-LX Fiber Optic Cable LengthFi

iLIMITED WARRANTYLimited Warranty Statement: SMC Networks, Inc. (“SMC”) warrants its products to be free from defects in workmanship and materials, un

MAKING NETWORK CONNECTIONS4-8Cable Labeling and Connection RecordsWhen planning a network installation, it is essential to label the opposing ends of

A-1APPENDIX ATROUBLESHOOTINGDiagnosing Switch Indicators Table A-1 Troubleshooting ChartSymptom ActionPower LED is Off • Check connections between th

TROUBLESHOOTINGA-2Power and Cooling ProblemsIf the power indicator does not turn on when the power cord is plugged in, you may have a problem with the

B-1APPENDIX BCABLESTwisted-Pair Cable and Pin AssignmentsFor 10BASE-T/100BASE-TX connections, a twisted-pair cable must have two pairs of wires. For 1

CABLESB-210BASE-T/100BASE-TX Pin AssignmentsUse unshielded twisted-pair (UTP) or shielded twisted-pair (STP) cable for RJ-45 connections: 100-ohm Cate

TWISTED-PAIR CABLE AND PIN ASSIGNMENTSB-3Straight-Through WiringIf the twisted-pair cable is to join two ports and only one of the ports has an intern

CABLESB-4Crossover WiringIf the twisted-pair cable is to join two ports and either both ports are labeled with an “X” (indicating MDI-X) or neither po

TWISTED-PAIR CABLE AND PIN ASSIGNMENTSB-51000BASE-T Pin Assignments All 1000BASE-T ports support automatic MDI/MDI-X operation, so you can use straigh

CABLESB-6Note that when testing your cable installation, be sure to include all patch cables between switches and end devices.Adjusting Existing Categ

C-1APPENDIX CSPECIFICATIONSPhysical CharacteristicsPorts20 10/100/1000BASE-T, with auto-negotiation4 10/100/1000BASE-T shared with 4 SFP transceiver s

iiWARRANTIES EXCLUSIVE: IF AN SMC PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, CUSTOMER’S SOLE REMEDY SHALL BE REPAIR OR REPLACEMENT OF THE PRODUCT IN

SPECIFICATIONSC-2Size44.0 x 17.1 x 4.3 cm (17.0 x 6.7 x 1.7 in.)TemperatureOperating: 0 to 40 °C (32 to 104 °F)Storage: -40 to 70 °C (-40 to 158 °F)Hu

STANDARDSC-3Out-of-Band ManagementRS-232 console portSoftware LoadingTFTP in-band, or XModem out-of-bandStandardsIEEE 802.3-2002 Ethernet, Fast Ethern

SPECIFICATIONSC-4

D-1APPENDIX DGERMAN INSTRUCTIONSEine Site Auswählen (Selecting a Site - German)Die Schalter können in ein Standard-19-Zoll-Ausrüstungsgestell oder auf

MONTAGE (RACK MOUNTING INSTRUCTIONS - GERMAN)D-2moglichen elektrischen Storungen verlegt wird, wie z. B. von Radios und Transmittern.• Sicherstellen,

GERMAN INSTRUCTIONSD-3So montieren Sie Geräte an ein Rack:1. Befestigen Sie die Metallwinkel mit den im Metallwinkel-Montageset erhältlichen Schrauben

MONTAGE (RACK MOUNTING INSTRUCTIONS - GERMAN)D-4

E-1APPENDIX EORDERING INFORMATIONTable E-1 TigerSwitch 10/100/1000 Products and AccessoriesProduct Number DescriptionSMC8024L224-port 10/100/1000 int

ORDERING INFORMATIONE-2

Glossary-1GLOSSARY10BASE-TIEEE 802.3 specification for 10 Mbps Ethernet over two pairs of Category 3 or better UTP cable.100BASE-TXIEEE 802.3u specifi

iiiCOMPLIANCESFCC - Class AThis equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the

GLOSSARYGlossary-2BandwidthThe difference between the highest and lowest frequencies available for network signals. Also synonymous with wire speed, t

GLOSSARYGlossary-3Full DuplexTransmission method that allows two network devices to transmit and receive concurrently, effectively doubling the bandwi

GLOSSARYGlossary-4Layer 2Data Link layer in the ISO 7-Layer Data Communications Protocol. This is related directly to the hardware interface for netwo

GLOSSARYGlossary-5Redundant Power Supply (RPS)A backup power supply unit that automatically takes over in case the primary power supply should fail. R

GLOSSARYGlossary-6

Index-1Numerics10 Mbps connectivity rules 4-7100 Mbps connectivity rules 4-71000 Mbps connectivity rules 4-61000BASE-LX fiber cable lengths 4-71000BAS

INDEXIndex-2IEEE 802.3z Gigabit Ethernet 1-5indicators, LED 1-3installationconnecting devices to the switch 4-2desktop or shelf mounting 3-6port conne

INDEXIndex-3standardscompliance C-3IEEE C-3status LEDs 1-3surge suppressor, using 3-1switch architecture 1-2switching, introduction to 2-1Ttemperature

INDEXIndex-4

COMPLIANCESivCE Mark Declaration of Conformance for EMI and Safety (EEC)SMC contact for these products in Europe is:SMC Networks Europe,Edificio Conat

38 TeslaIrvine, CA 92618Phone: (949) 679-8000Model Numbers: SMC8024L2Pub. Number: 150000023000H E052006-JC-R01FOR TECHNICAL SUPPORT, CALL:From U.S.A.

COMPLIANCESvSafety ComplianceWarning: Fiber Optic Port SafetyAvertissment: Ports pour fibres optiques - sécurité sur le plan optiqueWarnhinweis: Faser